TPO, EPDM, and modified-bitumen systems for additions, whole-house flat roofs, and small commercial — installed watertight and backed by 20–25 year membrane warranties. Leaking right now? We respond to flat-roof leak calls within 24 hours.
The roof where drainage matters more than the material
A flat roof has a low slope — about ¼ inch per foot — engineered to drain rather than pond. In the GTA the common systems are TPO, EPDM, and modified bitumen, lasting 20–30 years when installed right. The membrane choice matters, but the thing that actually decides how long a flat roof lasts is drainage and workmanship at the seams — which is exactly where we focus.
Drainage decides everything
Ponding water is the #1 cause of early flat-roof failure in the GTA. We build minimum ¼"-per-foot slope and verify drain capacity on every install — the unglamorous part that adds a decade.
Leaks fixed at the source
On a flat roof the leak is rarely above the stain — water travels the deck. We trace the true source at seams and penetrations, and respond to active leaks within 24 hours.
Repair before replace
Most flat-roof problems are a targeted repair, not a re-roof. We apply the >50%-of-replacement-cost rule honestly and tell you when a patch is the smarter spend.
The honest diagnosis
Leak or problem? Diagnose it first.
Before anyone quotes you a new roof, find out what's actually wrong. Pick the symptom and we'll tell you the likely cause, the urgency, and — honestly — whether it's a repair or a replacement. Most of the time it's a repair.
What's the flat roof doing?
Pick the closest symptom — we'll tell you the likely cause and whether it's a repair or a replacement.
Tell us the symptom
Most flat-roof problems are a targeted repair, not a full replacement — and we'll tell you which. Pick what you're seeing for the likely cause, the urgency, a real price band, and an honest repair-or-replace verdict.
Act fast — but it's very likely a repair
Almost always a seam or penetration, not a failed roof
An active leak feels like an emergency, and the water entry is — but the roof itself usually isn't failing. On a flat roof the leak source is rarely directly above the stain: water runs along the deck and finds a path down at a seam, a vent stack, a skylight, or an HVAC curb. If the membrane is otherwise sound and not past its life, this is a targeted repair, not a replacement. During an active storm-leak we'll tarp it first, then do the permanent fix once it's dry. We respond within 24 hours.
What we'd do
Find the true source (it's rarely above the interior stain)
Temporary tarp / containment if it's leaking right now
Heat-welded patch or re-flash the penetration once dry
Only escalate to replacement if the deck/insulation is saturated
Typical range: $400–$1,500 for a single-source repair; $1,000–$3,000 if a section of membrane needs replacing.
Seam or flashing failure where the membrane meets something
Most flat-roof leaks start exactly here: where the membrane is seamed to itself, or flashed up a wall, parapet, or around a vent or skylight. Old adhesive lets go, or a previous install never welded the seam properly. The good news is this is the most repairable failure of all — re-welding seams and re-flashing penetrations restores watertightness without touching the field of the roof. We only recommend more if we open it up and find the deck below has been wet for a long time.
What we'd do
Re-weld or re-seal the lifting seams
Re-flash walls, parapets, vents, and curbs properly
Add proper termination bars / counter-flashing where missing
Check the deck under the failed area isn't already rotted
Typical range: $500–$2,500 depending on how many seams/penetrations and access. Far cheaper than a re-roof.
Inadequate slope or blocked drainage — the #1 cause of early failure
Water that still sits 48 hours after rain is the single biggest killer of GTA flat roofs. Ponding accelerates UV and freeze-thaw breakdown right where the water sits. If the membrane is still sound, the honest fix is to restore drainage — clear or add drains, or build slope back with tapered insulation — not to replace the whole roof. But if ponding has already broken the membrane down or saturated the insulation underneath, that section (or the roof) is a replacement candidate. We'll measure and tell you which.
What we'd do
Clear or add drains / scuppers and verify capacity
Build minimum ¼"-per-foot slope with tapered insulation
Patch any membrane the ponding has already degraded
Replace insulation only where it's confirmed wet
Typical range: $800–$4,000 for drainage correction + tapered insulation; full replacement only if the membrane is spent.
Blisters and bubbles are pockets of trapped air or moisture under the membrane, often from a spot where adhesion was never quite right. A few isolated blisters that aren't leaking are mostly cosmetic and easy to cut, dry, and re-seal. The thing to watch is widespread blistering across the whole field — that points to an adhesion or moisture problem under the membrane, and that's a re-roof conversation. Most homes we look at are the former, not the latter.
What we'd do
Cut, dry, and heat-weld a patch over isolated blisters
Check whether the blister is dry (air) or wet (moisture)
Investigate the vapour path if blistering is widespread
Re-roof only if the whole field has lost adhesion
Typical range: $400–$1,200 for isolated blister repairs. Widespread field blistering is assessed for replacement.
Cracks, splits, and dry 'alligatored' patches are the surface telling you its UV protection is gone — most common on older modified-bitumen and built-up roofs. The honest answer depends on how widespread it is. A few isolated splits over an otherwise sound roof can be patched. But once the cracking is across the whole field and the roof is near or past its 20–30 year service life, patching is throwing good money after bad — a re-roof with a modern TPO or EPDM membrane is the better spend. We'll give you the straight call after measuring.
What we'd do
Patch isolated splits if the rest of the roof is sound
Assess the roof's age against its 20–30 yr service life
Re-roof with modern TPO/EPDM if cracking is widespread
We apply the >50%-of-replacement-cost rule honestly
Typical range: $500–$2,000 for isolated patching; $8,000–$22,000 for a residential re-roof if it's past its life.
An aging tar-and-gravel (built-up) roof at end of life
Gravel-ballasted built-up roofs were standard into the 1980s, and most are now well past their service life. Leak detection through gravel is miserable and patching a BUR roof is usually a short-term band-aid. The modern move is to strip the gravel and install a TPO or EPDM membrane: it weighs far less (important on older buildings), installs faster, and makes future leaks findable. If yours is still relatively young and only leaking in one spot we'll repair it — but most gravel roofs we see are replacement candidates.
What we'd do
Strip the gravel and assess the deck condition
Install a modern TPO or EPDM membrane (lighter, findable leaks)
Add tapered insulation to fix any ponding while it's open
Spot-repair instead only if the BUR roof is still young
Typical range: $10,000–$25,000+ to strip and re-roof a residential flat roof, depending on size and deck repairs.
Three solid systems, each best at something different. Answer three quick questions and we'll point you to the right membrane for your building and how you'll use it.
Step1 / 3
01
What's the flat roof on?
Different buildings and uses favour different membranes.
02
What matters most?
Be honest — it points us to the right system.
03
Any preference on the surface?
Membranes come in different colours and finishes.
Answer the three questions
We'll point you to the membrane that fits your roof, budget, and how you'll use it. Honestly, though — on a flat roof, who installs it matters more than which product. A great EPDM install beats a sloppy TPO one every time.
Best match: TPO
TPO is the right membrane for you
TPO — a white, reflective single-ply membrane with heat-welded seams — is the default best choice for most GTA residential flat roofs and small-commercial buildings in 2026. The heat-welded seams essentially fuse the whole roof into one piece, the reflective surface cuts summer cooling load, and manufacturer warranties run 20–25 years. It's our most-recommended system for new installs.
Heat-welded seams — the whole membrane becomes one piece
White / reflective surface lowers summer cooling costs
20–25 year manufacturer warranties
Best all-round value for residential + small commercial
EPDM — a proven rubber membrane — is the value pick with a 25+ year real-world track record in the GTA. Its dark surface suits roofs where reflectivity isn't a priority (shaded, low-visibility, or where you actually want some solar gain on a heated space below), and install cost is typically a touch lower than TPO. When budget and longevity matter more than a reflective surface, EPDM is hard to beat.
Proven 25+ year service life in GTA conditions
Typically a little lower install cost than TPO
Dark surface — fine where reflectivity isn't the goal
Modified bitumen — a multi-layer asphalt-based system — is the right answer when the roof will see foot traffic or carry a terrace, deck, or green roof. It handles point loads far better than single-ply membranes, which can be punctured underfoot. For a rooftop you'll actually walk on or build on, mod-bit is the durable choice; for a roof you'll never touch, TPO or EPDM is usually the better spend.
Multi-layer build handles foot traffic and point loads
Best for terraces, decks, and green-roof assemblies
Proven asphalt-based waterproofing, 15–30 yr life
We'll pair it with the right walking surface or pavers
Flat roofing demands precision. Here's how we ensure a watertight result every time.
Drainage engineered inHeat-welded / sealed seamsFlood or visual leak test
1
Roof Assessment & Survey
We thoroughly inspect your existing flat roof, identify problem areas, assess drainage, and document current conditions.
2
System Recommendation & Quote
Based on your building type, budget, and longevity goals, we recommend the best flat roofing system and provide a detailed quote.
3
Scheduling & Permits
We coordinate timing to minimize business disruption, pull necessary permits, and schedule material delivery.
4
Surface Preparation
We remove or prepare existing roofing, repair substrate damage, ensure proper drainage slopes, and install insulation as needed.
5
Membrane Installation
Our crews install your chosen roofing system with meticulous attention to seams, penetrations, and edge details—where most flat roof failures occur.
6
Quality Check & Warranty
We conduct flood testing or visual inspection, document the installation, and provide manufacturer and workmanship warranties.
Real GTA pricing
How much does flat roofing cost?
Most GTA flat roofing runs $8–$15 per square foot installed, with residential projects landing in the $8,000 – $25,000+ range. The biggest variables are membrane system, insulation depth, and the number of penetrations. Emergency leak repairs are priced separately — every estimate is itemized.
Project type
Typical size
Price range
What's included
Small residential flat roof
400–800 sq ft
$6,000 – $12,000
TPO or EPDM, rear addition or garage
Mid-size residential
800–1,500 sq ft
$10,000 – $22,000
Includes insulation, drip edge, flashing
Large residential / row home
1,500–2,500 sq ft
$18,000 – $35,000
Multi-day install, parapet + coping work
Small commercial
2,000–5,000 sq ft
$20,000 – $50,000
TPO with manufacturer warranty
Mid-size commercial
5,000–15,000 sq ft
$50,000 – $150,000
Higher-spec system, after-hours options
Emergency leak repair
Per repair
$400 – $1,500
24-hour response across the GTA
Skylight integration
Per skylight
$1,200 – $3,500
Includes flashing + waterproofing
Annual maintenance program
Per visit
$300 – $800
Bi-annual inspection, drain clearing
Pricing reflects typical GTA 2026 flat roofing rates. Commercial pricing varies based on warranty tier and after-hours scheduling. Emergency repair pricing assumes daytime weekday response; after-hours and weekend response has a premium. Every Buildoreno flat roof estimate is itemized — membrane, insulation, flashing, disposal, and any permit fees called out separately.
Reviewed by Patrick Grygoruk · Owner & Project Manager
25+ years in GTA exterior renovation · Ontario-registered contractor · WSIB-covered · permits managed for you. Meet the team
Honest answers
Flat roofing questions, answered
For most commercial applications in the GTA, we recommend TPO (thermoplastic polyolefin) or EPDM rubber roofing. TPO offers excellent energy efficiency with its reflective surface, while EPDM provides proven durability at a lower cost. The best choice depends on your building size, budget, and energy goals.
A properly installed flat roof typically lasts 20–30 years. TPO and EPDM membranes come with 20-25 year manufacturer warranties. Modified bitumen systems can last 25-30 years. Lifespan depends heavily on installation quality, drainage, and maintenance.
Yes, we offer flat roof repair services including emergency leak repairs. We'll identify the source of the leak—often at seams, penetrations, or flashing details—and provide either a targeted repair or recommend replacement if the roof has reached end-of-life.
Flat roofs require proper drainage design to prevent ponding water. We ensure adequate slope (minimum 1/4" per foot) and install drains, scuppers, or gutters as needed. Ponding water is the #1 cause of flat roof failure—we engineer it out from the start.
Flat roofing typically costs $8–15 per square foot installed, depending on the system chosen. This is often less expensive than sloped roofing materials on a per-square-foot basis. For commercial buildings, the larger roof area means material choice significantly impacts total cost.
Yes, we offer preventative maintenance programs for commercial flat roofs. Regular inspections catch small issues before they become expensive repairs. Most programs include bi-annual inspections, drain clearing, and minor repairs.
Gravel on a flat roof is a ballast layer over an older built-up roofing (BUR) system — it weighs the membrane down against wind uplift, blocks UV, and adds fire resistance. Modern TPO and EPDM membrane systems mechanically attach or fully adhere to the deck, so gravel isn't needed. If your existing flat roof is gravel-ballasted and failing, replacing it with a modern membrane system is usually faster, lighter, and easier to maintain.
Both. Residential flat roofs — rear additions, garages, modern infill builds, mid-century homes — are a significant part of our work. We install TPO, EPDM, and modified bitumen on residential roofs from 400 sq ft up to large row-home roofs. Pricing scales linearly with area and access; small residential roofs typically start at $6,000.
TPO and modified bitumen installations require above-freezing temperatures for proper adhesion and seam welding, so we typically schedule new installations April through November in the GTA. EPDM can be installed slightly later into the season. Emergency leak repairs continue year-round — we'll tarp and contain damage in winter and complete permanent repairs once temperatures cooperate.
We respond to flat roof leak calls within 24 hours during business days across the GTA. For active leaks during storms or off-hours, we can usually dispatch faster for temporary containment (tarping and water diversion) and schedule the permanent repair within a few days. Emergency leak response runs $400–$1,500 per repair depending on the cause and access.
Yes, but differently than pitched roofs. Modern flat roof assemblies are typically designed as 'warm roof' or 'compact roof' systems where insulation sits directly above the deck without traditional ventilation; this avoids condensation issues common in vented flat roof designs from the 1980s and earlier. We follow current Ontario Building Code requirements for the specific assembly being installed and can advise on which approach suits your project.
Yes. Flat-roof skylight integration is a common addition during membrane replacement — TPO and EPDM both handle skylight curb flashing cleanly, and installing skylights at the same time as the new membrane is faster and cheaper than retrofitting later. Pricing typically runs $1,200–$3,500 per skylight including flashing.
Membrane manufacturers warranty TPO and EPDM systems for 20–25 years (some commercial systems up to 30). Buildoreno backs the installation itself with a 5–10 year written labour warranty covering installation defects. The combined warranty package is provided at project close and is transferable on home sale — important for resale value.
Tear-off, new TPO membrane, drains and flashing, heat-welded seams, with a written workmanship warranty.
or about $64/mo†Financing coming soon
* Covers up to 370 sq ft of TPO at $8/sq ft on a single-level residential flat roof with clear access. Modified bitumen from $10/sq ft. Larger roofs and insulation upgrades are priced from your free measure. Our minimum project is $3,000. Plus HST; permits billed at cost.
$400 roof inspection, credited back when you hire us
A full walk of the roof, attic and flashing with photos and a written report. $50 refundable deposit to book; the fee is credited against the work (up to 10% of the quote).
† Illustrative monthly payment at 9.99% APR over 60 months, before HST. Financing is coming soon and subject to approval; terms may differ.
24-Hr Leak Response · Free Assessment
Leaking, or planning ahead?
Book a free flat-roof assessment — or call now if it's an active leak. We'll find the real source, tell you honestly whether it's a repair or a replacement, and itemize every cost.